Expert Power Control 8316-2: Remote controllable and outlet-metered power switch with high inrush relay

Remote controllable and outlet-metered power switch with high inrush relay

Remotely switched and per load outlet metered power control with 8 x IEC C13 sockets for usage in combination with a media management system. The power control can be used to switch connected electrical loads on and off and for current measurement. Up to 9 electrical quantities can be measured on the input side and per load outlet (see below). Two combined sensors (temperature, humidity and air pressure) can be connected to the two RJ45 connectors for environment monitoring. Thanks to standardised protocols such as HTTP/HTTPS, Telnet, RADIUS, MQTT and Modbus TCP, the device can be controlled with a media management system, a server or integrated into a monitoring software. Connecting to Crestron and Extron devices is done quickly, thanks to available drivers.
Toolless installation in media or IT racks (19 inches), furniture, pedestals and tables is made possible because the device’s rack ears are already attached. Each output can be switched individually. The outputs can be switched event-based by pre-set sensor thresholds and programmed schedules. The switching state and switch-on delays (0…9999 seconds) are freely adjustable for each Power Port.
The power control has an integrated overvoltage protection type 3. This overvoltage protection (OVP) prevents damage to the device and the connected electrical loads (max. L-N, N/L-PE 10 kA). Current peaks are prevented by automatic latency times of one second between the switching of several outputs. In addition, special high-inrush relays prevent the relay contacts from welding during inrush current peaks by withstanding currents of up to 80 A for short periods.
An easily readable LED display shows the relevant status information and the status of the outputs (on/off) directly on the device. This allows a quick overview of total current, IP address and sensor values.
Remote access to the device’s web server is possible via an RJ45 network connection and an RS232 interface. In addition, the power supply unit can be monitored and controlled while on the move via a mobile device app available free of charge. Furthermore, common security standards are supported (IPv6, SSL, SNMPv3).

• 1 power connection (IEC C20, max. 16 A),
• 8 load outputs (IEC C13, max. 10 A)
• 1 RJ45 network connection (10/100 Mbit/s)
• 1 serial interface RS232 (Sub-D, 9-pin)
• 2 sensor inputs (RJ45) for optional sensors

Technical data:
• Vertical mounting: 0 HU
• Dimensions (LxHxD): 69 x 6 x 7 cm (without rack ears)
• Weight: approx. 3.0 kg
• Max. current (total): 16 A
• Max. current (per port): 10 A
• Power consumption: approx. 5 W
• Operating temperature: 0-50 °C
• Storage temperature: -20 – 70 °C
• Relative humidity: 0 – 95 % (non-condensing)
• High-Inrush Relay: Type 16 A, 30 A up to 4s and 80A up to 20ms
• Overvoltage protection: max. L-N 10 kA

Switching function: Per load output
Measuring function: Total measurement at the input of the device and on output level
Measured quantities: voltage (V), current (A), frequency (Hz), phase angle (°), active power (W), reactive power (Var), apparent power (VA), power factor (PF), energy (kWh)
Display: 4-digit red LED display to show total current, IP address, sensor values and error messages; plain text displays (on/off) for the status of the outputs; three LED indicators for the status of the device, power supply and OVP
Supported protocols: SNMPv1, v2c, v3; HTTP, HTTPS; SSL, STARTTLS; TLS 1.1, 1.2, 1.3; Syslog; TCP/IP v4, IPv6; DHCP, Telnet, Radius, Modbus TCP, MQTT 3.1.1

Brand: GUDE
Type: 8316-2


Tender Spec as txt file                      Go to product