Switched and metered Power Control with High-Inrush relays Remotely switched and metered Power Control with 12 x IEC C13 for usage in combination with a media management system. The power control can be used to switch connected electrical loads on and off and for current measurement. Up to 9 electrical quantities dimensions can be measured on the input side, as well as residual current measurement (see below). Two combined sensors (temperature, humidity and air pressure) can be connected to the two RJ45 connectors for environment monitoring. Thanks to standardised protocols such as HTTP/HTTPS, Telnet, RADIUS, MQTT and Modbus TCP, the device can be controlled with a media management system, a server or integrated into a monitoring software. Connecting to Crestron and Extron devices is done quickly, thanks to available drivers. Toolless installation in media or IT racks (19 inches), furniture, pedestals and tables is made possible because the device’s rack ears are already attached. Each output can be switched and restarted individually. The outputs can be switched event-based by pre-set sensor thresholds and programmed schedules. The switching state and switch-on delays (0...9999 seconds) are freely adjustable for each Power Port. An automated reboot can be set individually per output using the integrated watchdog function (ICMP/TCP). The Power Control has an integrated overvoltage protection type 3. This overvoltage protection (OVP) prevents damage to the device and the connected electrical loads (max. L-N, N/L-PE 10 kA). Current peaks are prevented by automatic latency times of one second between the switching of several outputs. In addition, special high-inrush relays prevent the relay contacts from welding during inrush current peaks by withstanding currents of up to 80 A for short periods. An easily readable LED display shows the relevant status information and the status of the outputs (on/off) directly on the device. This allows a quick overview of total current, IP address and sensor values. Remote access to the device's web server is possible via an RJ45 network connection and an RS232 interface. In addition, the power supply unit can be monitored and controlled while on the move via a mobile device app available free of charge. Furthermore, common security standards are supported (IPv6, SSL, SNMPv3). Connections: - 1 power connection (IEC C20, max. 16 A), - 12 load outputs (IEC C13, max. 10 A) - 1 RJ45 network connection (10/100 Mbit/s) - 1 serial interface RS232 (Sub-D, 9-pin) - 2 sensor inputs (RJ45) for optional sensors Technical data: - 19 inch installation: 1 HU - Dimensions (LxHxD): 43.9 x 4.4 x 17.8 cm (without rack ears) - Weight: approx. 2.2 kg - Max. current (total): 16 A - Max. current (per port): 10 A - Power consumption: approx. 5 W - Operating temperature: 0-50 °C - Storage temperature: -20 - 70 °C - Relative humidity: 0 - 95 % (non-condensing) - High-Inrush Relay: Type 16 A, 30 A up to 4s and 80A up to 20ms - Overvoltage protection: Type 3, max. L-N, N/L-PE 10 kA - Watchdog (ICMP/TCP) for each outlet Switching function: Per load output Measuring function: Total measurement at the input of the device Measured variables: voltage (V), current (A), frequency (Hz), phase angle (°), active power (W), reactive power (Var), apparent power (VA), power factor (PF), energy (kWh), residual current measurement (mA) Display: 4-digit red LED display to show total current, IP address, sensor values and error messages; plain text displays (on/off) for the status of the outputs; three LED indicators for the status of the device, power supply and OVP Supported protocols: SNMPv1, v2c, v3; HTTP, HTTPS; SSL, STARTTLS; TLS 1.1, 1.2, 1.3; Syslog; TCP/IP v4, IPv6; DHCP, Telnet, Radius, Modbus TCP, MQTT 3.1.1 Brand: GUDE Type: 8041-1 Quantity: